↑ Return to Rules

Print this Page

Street Stock

2013 DIRTcar Stock Car Rules
TO ALL COMPETITORS/PARTICIPANTS

 The following are the 2013 DIRTcar Stock Car rules. All amendments supersede any
previous rules regarding any technical article and/or aspect.
 Under the guideline of the 2013 DIRTcar Stock Car rules any and/or rules and as stated
in the 2013 DIRTcar UMP Rule Book, all DIRTcar rules apply to all sanctioned divisions.
 The specifications published shall be considered a section of the “Official Rules and
Specifications” for all events, series and sanctions by World Racing Group. All sections
should be considered when determining specifications and governance.
15.0 DIRTcar Stock Car Rules
ANY CAR, TEAM AND/OR DRIVER THAT DOES NOT MEET THESE SPECIFICATIONS AND/OR EQUIPMENT
REQUIREMENTS WILL BE SUBJECT TO PENALTIES AS DETERMINED BY THE DIRTcar and/or World Racing
Group OFFICIALS.
15.1 – Engine
A.) The engine and body must be manufactured by the same company and be within the same manufacturer’s model
line when introduced into competition.
B.) The number one (1) spark plug must align itself in a perpendicular line with the center of the upper ball joint for
each manufacturer.
C.)The engine block must be cast iron from an OEM manufacturer. In addition to the factory OEM blocks only the GM
Bowtie blocks with the casting numbers of 10051181, 10051182 and 10051183 will be permitted. The SHP DART
Block will be permitted for competition.
D.) Aluminum engine blocks will not be permitted.
E.) Cast iron cylinder heads of any make are permitted.
F.) Aluminum cylinder heads of any origin will not be permitted.
G.) Roller tip rocker arms will be permitted.
H.) Roller Cams of any-type will not be permitted. Roller and/or mushroom-type lifters will not be permitted.
I.) Cast Iron or Aluminum intake manifolds will be permitted.
J.) Cast Iron or aftermarket exhaust headers will be permitted. The direction of the exhaust flow must exit away from
the car and the track surface.
K.) HEI distributors will be permitted. The OEM firing order for the engine must be maintained.
L.) Racing-type and/or specific racing-type distributors will not be not permitted.
M.) MSD boxes and/or any other ignition amplifier boxes of any type will not be permitted.
N.) Conventional or Aluminum radiators will be permitted
O.) One 500 CFM 4412 Holley unaltered carburetor is required. The local track rules reserve the right for carburetors
to be claimed and/or changed (i.e. “swapped”) for competitive analysis and/or inspection.
1.) The original choke tower must remain in its stock position and configuration.
2.) The choke blade may be removed.
3.) Any other alterations to the body of the carburetor, internal working mechanisms, venturis, throttle plate and/or
any other part and/or component of the carburetor will not be permitted
4.) Carburetor jets may be replaced and/or adjusted as an engine tuning method.
5,) Only mechanical fuel pumps will be permitted.
P.) All cars must be equipped with an operable starter in working condition.
15.2 – Transmission & Driveline
A.) TRANSMISSION AND DRIVELINE
All Types:
a.) The transmission must have a minimum of at least two forward gears and one reverse, plus neutral position.
b.) With motor running and car in still position, the transmission must be able to engage the car in gear and the car
must be able to move forward, then backward.
c.) Only OEM production type transmissions will be permitted – two speed, three speed, four speed and automatic.
d.) Five speed (or more) transmissions, “in and out” boxes, and/or quick change will not be permitted.
e.) All functioning shift levers must be located in OEM position. The flywheel and/or flexplate must be bolted directly
to the end of the crankshaft, and the pressure plate must be fastened and/or bolted directly to the flywheel/flexplate.
f.) Only one (1) flywheel/flexplate will be permitted. All driveline components within the bell housing must rotate
consistent with the RPM of the engine while the car is in any gear. Only unaltered an unaltered OEM flexplate and/or
an OEM replacement will be permitted.
g.) Bert and/or Brinn and/or Falcon type transmissions will not be permitted.
Manual:
a.) Any manual-type transmission must be in an OEM or OEM replacement case.
b.) In manual-type applications only an external steel and/or aluminum, single or multi-disc clutch inside an explosionproof
steel bell housing will be permitted. The bell housing must be a minimum 270 degrees around top of
clutch/flywheel area.
c.) Special purpose, after-market type racing transmissions will not be permitted.
Automatic:
a.) Any automatic-type transmission must remain in an OEM or OEM replacement case, with a functioning OEM
appearing pump.
b.) An aluminum OEM bell housing and/or aftermarket explosion-proof aluminum bellhousing will be permitted.
c.) The original OEM bell housing must have an approved scattershield constructed of minimum 0.125” inch by three
(3) inch steel, 270 degrees around flexplate. Manual bump starts will be permitted.
15.2.1 Drive Shaft
A.) The driveshaft must be a minimum two (2) inch diameter and made from magnetic steel.
B.) The driveshaft must be painted white and clearly labeled with the car number on the white portion of the
driveshaft.
C.) Only magnetic steel slip-yokes will be permitted.
D.) A 360-degree drive shaft loop will be required and must be constructed of at least 0.25” inch by two (2) inch
magnetic steel, and/or one (1) inch diameter tubing, mounted six (6) inches behind the front universal joint. A second
drive shaft hoop is recommended and must be placed within 12” inches of the front universal joint.
15.3 – Chassis
A.) Only American manufactured cars and/or full-size “uni-body” type cars will be permitted. Sports car chassis for
the Chevrolet Camaro / Pontiac Firebird and/or the Ford Mustang from 1967 to 1985 will be permitted.
B.) All vehicles must maintain a minimum of 107” (inch) wheelbase.
C.) Altering of stock frame, with the exception of repair to the original frame to maintain original specifications will not
be permitted. Repairs that will be acceptable will include patching of holes and/or rust(ed) areas of the frame. Repairs
will be approved at the discretion of DIRTCAR Officials and/or local track officials.
D.) The rear frame may be replaced from the rear shock absorber mounts toward the rear of the car.
15.4 – Weight
A.) The minimum weight requirement at all times will be 3,200 lbs (pounds).
B.) All weights must be securely mounted with two (2) ½” (inch) bolts securing them to the frame in a positive
manner. The weight(s) must be painted white with the car number clearly marked on them. All weights must be
mounted under the body of the car.
15.5 – Fuel Cells and Fuel
A.) Only gasoline-type fuels will be permitted.
B.) The fuel cell must be securely mounted in the rear of the car and secured with straps. It is recommended that the
fuel cell be mounted solidly to the rear frame rails of the vehicle in a fabricated manner.
C.) All fuel cells must be enclosed in a metal container.
D.) The fuel cell must be a steel container with a minimum of two (2) one (1) inch by 1/8” (inch) steel straps on each
side of the container to mount the fuel cell.
E.) Only gasoline will be permitted. Methanol and/or any other type of fuel and/or any type of fuel additive will not be
permitted.
15.6 – Body
A.) The body, frame and engine must match the manufacturer. The body, body mounting position and overall
appearance must retain all stock OEM dimensions and original body line and contours and must be centered over the
wheels. Shortening and/or overlapping of the body panels will not be permitted. All glass, chrome and
upholstery must be removed from body prior to competition. The body must be made from magnetic steel. Bodies
that appear to be flat sided and/or do not have stock contours and appearance and/or appear to be fabricated
from scratch will not be permitted.
The following are the critical body dimensions;
1.) A minimum roof height of 51”-inches
2.) A minimum of 6”-inches ground clearance, nose and/or the side rocker panel(s).
3.) The minimum door length will be 28 ½”-inches.
4.) The minimum window opening will be 14”-inches measured vertically from the top of the door to the
bottom of the drip edge on the roof.
5,) Stock and/or after-market ‘production-type’ piece diagrams may be used for reference in regard to
dimensions, proper mounting position and location for any standard body.
B.) The top and/or roof of the car may be removed to install the roll cage assembly, but it must be replaced and
fastened in its stock OEM location.
C.) The front windshield opening must be covered with ½” x ½”-inch and/or 1” x ½”-inch wire mesh. It is also
recommended that three (3) support bars fabricated from magnetic steel tubing, a minimum of 1”-inch diameter and
.095” wall thickness be spaced equally in front of the driver and welded to the top roll cage bar and the dash bar of
the roll cage in a vertical manner.
C.) The inner door panels may be altered for the placement of the door bars in the roll cage assembly.
D.) The floorpan and firewalls must be stock in appearance and be complete on both the driver and
passenger side of the vehicle. The front firewall must be a maximum of 12”-inches behind the rear edge of
the engine block. The floorpan and firewalls (front and rear) may be repaired and/or fabricated, but must retain stock
appearance and stock material thickness. The minimum thickness for replacement material / patches on the floorpan
will be .060” with the maximum being .125”-inch magnetic steel. The only alterations permitted to the floorpan and/or
firewall will be for the proper engine setback. Any alterations to the floorpan and/or firewall material thickness will not
be permitted.
1.) Repair of the floorpan or firewall patch, if needed, must be made with magnetic steel with minimum
thickness of the original in the stock location. Repair patch is limited to the repair or hole only.
2.) Floorboard may be cut for the mounting of the roll cage only.
3.) The floorboard must have a driveshaft tunnel.
3.) Firewall(s) must be sealed and complete. Open holes in the firewall will not be permitted.
4.) The front of the rear firewall must maintain the same height as the top of the front of the dashboard.
5.) The maximum length of the dashboard from the front firewall to the edge of the dashboard panel will be
24”-inches.
6.) The firewall must be at a 90-degree angle from the floorpan.
E.) The driver and passenger compartment must remain open from left to right exposing the stock-appearing floor
pan and to the rear seat firewall and shelf. There may be an enclosure on the passenger side of the vehicle, a
maximum of 6”-inches in width from the top outside edge of the door, for the purpose of routing and covering the fuel
line as it passes through the driver compartment, unless a conduit is used. Additional sheet metal including cockpit
type enclosures and/or any modifications within the interior of the car and/or driver compartment area will not be
permitted.
F.) The trunk floor area may be cut to allow for the mounting of the fuel cell.
G.) The body, including fenders, quarters, hood, roof, decks doors must be magnetic steel and remain stock or
approved stock in appearance.
H.) The body must be mounted in its stock OEM location and centered between the wheels. Chopping and/or
channeling of the body will not be permitted.
I.) Exposed tubing and/or bracing outside of the bodyline of the car will not be permitted with the exception of rub/side
rails.
J.) Plastic aftermarket front nose will be permitted provided they are approved and stock appearing for the year, make
and model of the car. Late Model type aerodynamic noses will not be permitted.
K.) Rub/side rails may be attached flush to the body from the fender well to the rear quarter panel.
L.) A maximum seven (7) inch visor/sun shield may be added to the top of the windshield opening. The window
openings, front and/or rear, driver and/or passenger side must retain their stock OEM dimensions.
M.) Mirrors of any type are not permitted.
N.) The back of the hood must be sealed off from the driver’s compartment.
O.) The front bumper must remain stock. Sharp edges will not be permitted. Both sides and ends of the bumper must
be capped. Tube-type front bumpers will be permitted. Tube-type bumpers must have capped ends.
P.) The rear of the car must be enclosed. The rear bumpers may be covered and must have round edges and
connect solidly to the frame. After-market rear bumper covers will be permitted provided they are approved and stock
appearing for the year, make and model of the car.
Q.) Front and/or rear spoilers of any type will not be permitted. Spoilers that are molded as a part of an OEM type
application will be permitted.
15.7 – Suspension
A.) All suspension components must remain stock in their OEM mounting locations for the year make and model of
the vehicle with the exception of racing shocks and/or springs that are mounted in stock locations.
B.) The steering shaft may be a collapsible shaft
C.) Aftermarket steering wheel and quick release are permitted.
D.) Steering quickening devices are permitted.
E.) After-marketing steering components will be permitted. After market steering components must be similar and/or
replacement in type to the OEM application for the make and model of the vehicle.
F.) Only stock OEM-type bolt-in upper ball joints will be permitted. Adjustable and/or truck type ball joints will not be
permitted. Cutting and/or alterations to the frame will not be permitted to accept any other type or style of ball joint.
G.) Only DIRTcar approved Tubular-type A-Frames, mounted in their stock OEM location will be permitted. The AFrames
may be reinforced along the edges by welding round stock. Cutting and/or changing lengths of the A-Frames
will not be permitted.
H.) Only stock OEM and/or Ford 9”-type rear ends will be permitted for competition. Quick change rear ends will not
be permitted.
I.) The lower rear trailing arms must remain in their stock OEM length, format and length, from the original
OEM application and measurement system (English or Metric) and must remain specific to their particular
chassis/frame and must be the same length on each side. The lower rear trailing arms must be mounted in the
stock location. Additional holes in the frame and/or rear end will not be permitted.
J.) The upper rear trailing arms may be altered (shortened and/or lengthened) to obtain the correct pinion angle.
K.) Aftermarket bushings will be permitted, but the arm must not be altered in any manner. Slots and/or adjustable
rod ends will not be permitted.
L.) Leaf-type springs will be permitted. Only stock OEM-type magnetic steel leaf spring(s) stack(s) will be permitted.
Single leaf, mono-type-leaf and/or any type of slider and/or any composite leaf-type applications will not be permitted.
M.) Coil-over applications of any-type will not be permitted.
N.) Aftermarket coil springs will be permitted. The coil spring location may be altered, however, the centerline of the
axle tube may not be any further forward than the front of the spring or not further back than the rear of the spring.
O.) Only magnetic steel body, non-adjustable shock absorbers will be permitted. The DIRTcar approved –
A-type shock absorbers displaying the DIRTcar “Approved” decal will be permitted to compete.
P.) Weight jacks will be permitted.
Q.) Hydraulic ratchet and/or electric weight jacks are not permitted.
R.) Only stock-type OEM brakes will be permitted. Disc brake(s) will be permitted on the rear brake(s) provided that
the rear brake caliper(s) match the front brake calipers. Alterations to the rear brake rotors, to fit the rotor to the rear
only, will be permitted. All four corners must be in working condition prior to and following the completion of
competition. After market brake pedals will be permitted. Brake bias adjusters and valves will not be permitted.
S.) Suspension components that are adjustable within driver compartment of any-type will not be permitted.
15.8 – Wheels and Tires
A.) A maximum 8” (inch) wide steel racing wheel will be permitted. Aluminum and/or magnesium and/or mag-type
and/or homemade wheels will not be permitted. one (1) inch magnetic steel lugnuts will be permitted on all four
corners of the vehicle.
B.) Only Hoosier E-Mod tires; compounds, D, H and/or A will be permitted. The DCM 400 will be permitted.
The local track rules may prevail on the specific tire and tire choice rule of the three offered Hoosier E-Mod
compounds.
C.) Any type of alteration, chemical or mechanical, to the face and/or sidewall of the tire will not be permitted.
D.) A bead lock will be permitted on the right rear tire only.
15.9 – Personal Protection Equipment
15.9.1. General
A.) It is the sole responsibility of each competitor for the effectiveness and proper installation, per the manufacturer’s
specifications to be adequate for competition at every event. Each competitor is expected to investigate and educate
themselves for continuing improvement regarding their own personal safety equipment.
15.9.2 Seat Belt/Restraint System
A.) It is recommended that each car be equipped with an SFI 16.5 or SFI 16.1 approved seat belt restraint system
until the date of the belt expiration (usually two years). Seat belts restraint systems shall be installed in accordance
with the directions and application of the system supplier or manufacturer.
B.) Seat belt webbing that comes into contact with any sharp or un-radiused metal edge should be protected from
that edge by means of push on grip vinyl trim. Seat manufacturers supply the seat with trim protecting the webbing
from abrasion or cutting under impact conditions and should be used to their specifications.
C.) It is the responsibility of the driver, not the Officials or the Promoter to ensure that his/her seat belt restraint
system and all components are SFI approved, correctly installed, maintained and properly used.
15.9.3 Protective Clothing
A.) Each driver should wear a fire resistant uniform meeting the SFI 3.2A/5 specification and display a valid SFI
3.2A/5 label.
B.) Each driver should also wear fire resistant accessories that effectively cover the remaining parts of the body.
Shoes and gloves should meet the SFI 3.3 specification and display a valid SFI.3label.
15.9.4 Seats
A.) It is recommended that an aluminum seat built specifically for the purpose of competition in auto-racing events be
required
B.) High-back Aluminum (stockcar style) seats should be securely mounted to the frame as recommended/required
by seat manufacturer and chassis manufacturer.
C.) The seat must be mounted near the stock OEM location of the front seat for the year, make and model of
the specific vehicle. Seats mounted past the rearward edge of the stock location on the driver’s side of the
vehicle will not be permitted.
D.) Head rest (behind the head) should include padding. All areas surrounding the head should have padding
E.) A right head net or support is required. Head nets must be equipped with quick release mechanisms
F.) The seat must be mounted a minimum of 30” (inches) from the centerline of the rear end, measured at any
point of the rear of the seat.
15.9.5 Helmets
A.) Driver should wear a full face helmet, with at least a valid SA 2000 or SA 2005 Standard Snell and/or a valid SFI
31.1, SFI 31.2 or SFI 31.1 2000 label.
B.) The driver should wear the helmet in accordance with the directions provided by the helmet manufacturer and/or
supplier.
C.) If a head and neck restraint system is connected it should conform to the manufactures mounting instructions.
D.) Head and Neck restraints are strongly recommended.
15.9.6 Other
A.) No sharp or protruding edges in or around the driver compartment, which would impede the driver’s rapid exit
from the car.
B.) Windshield screens with a minimum of .090 inch screens must be securely fastened
C.) An electrical engine shut off switch is required. The switch must be clearly labeled and within the reach of the
driver.
D.) A fuel shut off valve is recommended and should be utilized. The valve should be clearly labeled and within
reach of the driver. The fuel line must not enter the driver compartment.
E.) Flame retardant seat, roll bar, knee and steering pads or padding are recommended
15.10 – Roll Cage
A.) A minimum 4-point competition roll cage is required. The roll cage must be constructed of magnetic steel tubing
that is a minimum of 1 ½” in diameter, with a minimum tubing thickness of .095 (wall thickness). The roll cage must
be located within the stock OEM parameters of the doors of the vehicle. Roll cages that are moved toward the rear
of the car and/or offset will not be permitted.
B.) A minimum of three (3) horizontal door bars are required on each door.
C.) A minimum of three (3) driver protection bars are required in the windshield.
D.) Front and rear bars that pass through the firewall will be permitted, with one (1) kicker bar to the frame.
E.) A radiator protection bar will be permitted.
F.) There must be a minimum of 40”-inches between the outside edge of the front and rear down bars at the
top of the door panel. A maximum of 41”-inches (48”-inches on 1988-1996 GM-type bodies) from the top
center of the windshield to the front edge of the rear hoop and a maximum of 13”-inches (20”-inches) for
1988-1996 GM-type bodies) to the front edge of the top halo. The
G.) The top halo must be a minimum of 40”-inches across outside-to-outside.
H.) The rear hoop must be a maximum of 12”-inches in from the bottom of the opera window.
F.) The rear vertical roll bar hoop must be mounted on the rear body mount in the center section of the frame
a maximum of 81”-inches rearward of the centerline of the right front wheel/spindle. Rear vertical roll bar
hoops mounted on the rear frame rails (rearward of the rear body mounts) will not be permitted. The rear
vertical roll bar hoop of the roll cage should be perpendicular to the frame and must not exceed a ten (10)
degree variation from perpendicular in its vertical rise from the frame.
15.11 – Other
A.) Any battery that is mounted inside the driver’s compartment must be completely enclosed in a marinetype
box, with a lid and mounted securely.

Permanent link to this article: http://www.maconracing.com/?page_id=270

4 pings

  1. locksmiths finder

    … [Trackback]

    [...] There you will find 36215 more Infos: maconracing.com/?page_id=270 [...]

  2. locksmith finder

    … [Trackback]

    [...] Read More: maconracing.com/?page_id=270 [...]

  3. lol boost

    … [Trackback]

    [...] Read More here: maconracing.com/?page_id=270 [...]

  4. Little Shop of Os

    … [Trackback]

    [...] Find More Informations here: maconracing.com/?page_id=270 [...]

COMMENT ON THIS ARTICLE!